Samsung TS-L633L RPC1 here

Simri · **Joined:** Mon Sep 08, 2008 2:21 pm **Posts:** 4

I decide to do som test on my Samsung TS-L633L (HP OEM Firmware 0400)
Flashed SC01 firmware via Tsdnwin.exe -NOCHECK on my TS-L633L and the worked after reboot,
RPC1 firmware is not available for TS-L633L.
Checked TS-L633L SC01 firmware in Hex editor for Crossflashing and found this name inside TS-L632N so am downloaded TS-L632N-SC02 RPC1 and flashed via Tsdnwin.exe -NOCHECK and worked after reboot and now the driver is RPC1.

Now im tested to use MediaCodeSpeedEdit to patch TS-L632N SC03 to RPC1 and after im compare org vs rpc1 in Hex Workshop and put the patch code in TS-L633L SC01
(found all replace code) flashed via Tsdnwin.exe -NOCHECK and worked after reboot and now i have Samsung TS-L633L RPC1 on my HP Compaq Presario CQ50-100 Notebook PC

Flash Test
TS-L633L 0400-> TS-L633L SC01 -> TS-L632N SC01-> TS-L632N SC01 RPC1-> TS-L632N SC02 RPC1 -> TS-L632N SC03 RPC1-> TS-L633L SC01 RPC1

chef · **Posted:** Mon Sep 08, 2008 8:26 pm

Long way to success.

Could you please post the Discinfo output?

Simri · **Joined:** Mon Sep 08, 2008 2:21 pm **Posts:** 4

Right now can not use/get info from CQ50-100 Notebook PC (Corrupt bios) so im must wait to get USB floppy to do Phoenix Bios Crisis Recovery disk.

Puma · **Posted:** Tue Sep 09, 2008 7:39 pm

please leave some feedback if anyone has used this

Simri · **Joined:** Mon Sep 08, 2008 2:21 pm **Posts:** 4

Now my CQ50-100 Notebook works

Label on Samsung TS-L633L (SATA)
TS-L633L/HPMH 6Gxxxxxxx F/W=0400
H/W:B Ver.L MAY 2008

Code:

DISCINFO VERSION   : 1.7.0 BETA.12
VENDOR             : TSSTcorp
MODEL              : CDDVDW TS-L633L 
REVISION           : SC01
VENDOR SPECIFIC    : SC 
LOADING MECHANISM  : Tray
SERIAL NUMBER      : TS-L633LFirm
NUMBER VOL. LEVELS : 256
BUFFER SIZE        : 2048KB
TOSHIBA CODE       : OEM SC
TOSHIBA MODEL      : 
INTERFACE          : ATAPI
RPC2 SCHEME        : NO
ANALOG AUDIO PLAY  : YES
COMPOSITE OUTPUT   : NO
DIGITAL PORT-PORT1 : NO
DIGITAL PORT-PORT2 : NO
READ UPC CODE      : YES
MULTISESSION READ  : YES
MODE 2 FORM 1      : YES
MODE 2 FORM 2      : YES
READ ISRC CODE     : YES
READ BAD CODE      : NO
BUFFER UNDER-RUN   : YES
MT. RAINIER        : NO
CAN READ CDR       : YES
CAN READ CDRW      : YES
CAN READ CDRM2     : YES
CAN WRITE CDR      : YES
CAN WRITE CDRW     : YES
CAN TEST WRITE     : YES
CAN READ DVD-ROM   : YES
CAN READ DVD-R     : YES
CAN READ DVD-RW    : YES
CAN READ DVD-RAM   : YES
CAN READ DVD+R     : YES
CAN READ DVD+RW    : YES
CAN WRITE DVD-R    : YES
CAN WRITE DVD-RW   : YES
CAN WRITE DVD-RAM  : YES
CAN WRITE DVD+R    : YES
CAN WRITE DVD+RW   : YES
MAX CDR READ SPEED : 24
MAX CDR WRITE SPEED: 24

Schtiel · **Joined:** Tue Sep 16, 2008 3:03 pm **Posts:** 1

I checked it on my HP Pavilion dv5-1050 laptop, works fine. Thank you very much for firmware!

rameshb_v · **Joined:** Sun May 22, 2005 12:27 pm **Posts:** 12

Hi;

Can any one confirm if I can flash this firmware for TS-L632M Drive ? Are both of them same ?

Simri · **Joined:** Mon Sep 08, 2008 2:21 pm **Posts:** 4

rameshb_v wrote:

Hi;

Can any one confirm if I can flash this firmware for TS-L632M Drive ? Are both of them same ?

i dont know if this possibel.
You can use MediaCodeSpeedEdit 1.1.0.18 to patch TS-L632M SC0x firmware to RPC1.

rameshb_v · **Joined:** Sun May 22, 2005 12:27 pm **Posts:** 12

Simri wrote:

i dont know if this possibel.
You can use MediaCodeSpeedEdit 1.1.0.18 to patch TS-L632M SC0x firmware to RPC1.

I downloaded it and successfully patched to RPC1. Thank you.

chchyong89 · **Joined:** Mon Oct 20, 2008 6:11 pm **Posts:** 2

i am using vista X64
with compaq CQ40-125AX
through the devide manager, i get to know my dvd burner is TS-l633l 0400..
i download the TSDNWIN to flash, but once i click the search and select the download firmware from above, it get me "the firmware is not compatible with the selected drive, please contact blablabla....."
can anyone guide me.. sorry, i am newbie :cry:

Puma · **Posted:** Mon Oct 20, 2008 6:39 pm

chchyong89 wrote:

i am using vista X64
with compaq CQ40-125AX
through the devide manager, i get to know my dvd burner is TS-l633l 0400..
i download the TSDNWIN to flash, but once i click the search and select the download firmware from above, it get me "the firmware is not compatible with the selected drive, please contact blablabla....."
can anyone guide me.. sorry, i am newbie :cry:

use discinfo and post its output

chchyong89 · **Joined:** Mon Oct 20, 2008 6:11 pm **Posts:** 2

i just try change the name to "-nocheck".. @.@, it really work...=.=!
by the way, discinfo neverwork on my vista64

stefanotn68 · **Joined:** Mon Nov 03, 2008 11:06 am **Posts:** 1

I have Hp dv5-1070el with ts-L633L cdrom

i have flashed to RPC1...

Is it possible to flash to sc02 (original Samsung firmware)???
I tried but i gave me an error ....

thk for reply

stefano

hp2008 · **Joined:** Thu Nov 06, 2008 6:11 pm **Posts:** 1

hello

i have the same problem with my hp notebook.
when i try to change the firmware with tsdnwin it tells me: "this firmware is not compatible with ..."

what do you mean with Tsdnwin - nocheck???

Puma · **Posted:** Thu Nov 06, 2008 7:29 pm

hp2008 wrote:

hello

i have the same problem with my hp notebook.
when i try to change the firmware with tsdnwin it tells me: "this firmware is not compatible with ..."

what do you mean with Tsdnwin - nocheck???

post discinfo output from your drive

amadeus666 · **Joined:** Sat Nov 22, 2008 10:23 am **Posts:** 1

Hello,

I've got also the same message : The firmware is not compatible ...

My notebook is a HP Pavilion dv5-1130

Attachment:

DiscInfo.png [ 15.69 KiB | Viewed 16306 times ]

Puma · **Posted:** Sat Nov 22, 2008 2:15 pm

-nocheck is the command you input, so the flasher doesn't check the firmware revision, and thus flashes the drive

smiler51 · **Joined:** Tue Nov 25, 2008 8:37 am **Posts:** 3

Hey guys, for all of you that have a problem with "-nocheck" and how to use it, you need to start the program through the ms-dos prompt. copy and paste the file onto your C:\ drive and then type into the ms-dos prompt: c:\Tsdnwin.exe -NOCHECK

After this you can select the file you want to use to flash your DVD and it should work. Took me ages to figure out. I was already trying to edit the binary file of the firmware and the .exe file of the tsdnwin program. Lol...

Hope that could help someone!

Puma · **Posted:** Tue Nov 25, 2008 12:18 pm

smiler51 wrote:

Hey guys, for all of you that have a problem with "-nocheck" and how to use it, you need to start the program through the ms-dos prompt. copy and paste the file onto your C:\ drive and then type into the ms-dos prompt: c:\Tsdnwin.exe -NOCHECK

After this you can select the file you want to use to flash your DVD and it should work. Took me ages to figure out. I was already trying to edit the binary file of the firmware and the .exe file of the tsdnwin program. Lol...

Hope that could help someone!

good summary, we would hope, members would readup on how these things work, hopefully this will be a good aid

chef · **Posted:** Tue Nov 25, 2008 9:04 pm

Hm, makes me wonder if anyone here still remembers the time when windows still were what they are called - windows...?!
Nothing about click & clack. No GUI, no colour overkill. Just plain 2 colours. :mrgreen:

Gimme a sign if you need a commandline / DOS / *nix / shell lesson. :wink:

hokutoshinken · **Joined:** Thu Jan 15, 2009 3:47 pm **Posts:** 1

As I didn't get an answer from simri I ask here.I also flashed My HP OEM TS-L633L DVD writer from 0400 firmware to rpc1 sc01 firmware does anybody know where I can get back (download) my origin 0400 firmware in case of problems. Apperently an SC03 firmware is out. How can I edit it to region free ???

smiler51 · **Joined:** Tue Nov 25, 2008 8:37 am **Posts:** 3

Hey Guys,

i have a quick question. I flashed my drive with this firmware version. The only problem is that i can only burn at 10x or higher speed. I want to be able to burn at slower speed like 1x.

What do i have to change in the firmware to be able to do this?

Thanks

Smiler51

Puma · **Posted:** Sun Jun 14, 2009 4:44 pm

smiler51 wrote:

Hey Guys,

i have a quick question. I flashed my drive with this firmware version. The only problem is that i can only burn at 10x or higher speed. I want to be able to burn at slower speed like 1x.

What do i have to change in the firmware to be able to do this?

Thanks

Smiler51

to have quality media, then there is no need to burn at such low speeds, especially 1x, its not this myth of i must burn 1x for games, buy quality media

chef · **Posted:** Sun Jun 14, 2009 5:43 pm

smiler51 wrote:

Hey Guys,

i have a quick question. I flashed my drive with this firmware version. The only problem is that i can only burn at 10x or higher speed. I want to be able to burn at slower speed like 1x.

What do i have to change in the firmware to be able to do this?

Thanks

Smiler51

Useless attempt & stupid myth in one case....

smiler51 · **Joined:** Tue Nov 25, 2008 8:37 am **Posts:** 3

I mainly use Verbatim media, but for some reason, my Navigation system always has problems reading the CD's/DVD's if they are burned at a high speed.
Then there is of course the problem that Companies always switch their suppliers. One time they buiy the blank Media form this company, the next day from another.

The Firmware Page

Samsung TS-L633L RPC1 here

Who is online