|
Portal Board index » .:: Firmware Flashing ::. » DVD-RW/+RW/RAM Firmware
All times are UTC [ DST ]
|
| Author |
Message |
|
|
 Posted: Wed Oct 10, 2007 7:00 pm |
|
Joined: Mon Oct 08, 2007 7:25 pm
Posts: 7
|
|
Thank you.
Nothing seems to change:
DVRFlash v2.2 : Pioneer DVR firmware flasher
by Agent Smith, et al., November 2005
Commandline:
/Users/Marcello/Desktop/DVRFlash_v2/mac/DVRFlash
Device parameter was not given, detecting all DVR drives:
Device : A:
Vendor : PIONEER
Model : DVD-RW DVR-108
Revision : 1.18
Status : RPC-1 (region free)
Now run DVRFlash again, from the command prompt, using
one of the device(s) listed above as first parameter
Press the Return key to exit
Dvrflash -v A:
logout
[Processo completato]
|
|
| Top |
|
 |
|
|
Posted: Thu Oct 11, 2007 7:54 am |
|
Joined: Mon Oct 08, 2007 7:25 pm
Posts: 7
|
|
I just launch the application and then after it gives me infos about the drive by itself, I type the command You said. My macos is in italian, could that make any difference?
If I am bothering you I apologize.
I have virtualPC, too
can you direct me to a thread where I can understand how to perform the same operation with vPC if it is easyer?
Many thanks
Marcello
|
|
| Top |
|
|
|
|
Posted: Sat Oct 13, 2007 8:05 pm |
|
Joined: Sat May 22, 2004 12:37 pm
Posts: 247
|
marcello.dolcini wrote: I just launch the application and then after it gives me infos about the drive by itself, I type the command ... There's the problem; quite a common one 
Take a look at this thread and my comments in there.
|
|
| Top |
|
|
|
|
Posted: Sat Oct 20, 2007 8:11 pm |
|
Joined: Sat Oct 20, 2007 11:20 am
Posts: 3
|
|
Hi,
I have a problem for which i can not find a solution. I
|
|
| Top |
|
|
|
|
Posted: Sat Oct 20, 2007 11:12 pm |
|
| Puma |
| Administrator |
 |
Joined: Tue May 11, 2004 3:02 pm
Posts: 10124
Location: UK
|
Quote: i thinks something in windows system because when i try to
open the data of my burned DVDs a message come and tell me:
"access no possible" and other time tell me: disk is damage or no compatible with windows
1) try reading them in safemode
2) unistall all ide drivers and restart the system
these problems are more system related than firmware
_________________
Read The FAQ Firmware Request Rules
MCSE Thread Utilities
|
|
| Top |
|
|
|
|
Posted: Sat Oct 20, 2007 11:18 pm |
|
| Coaster |
| Posting Wizard |
 |
Joined: Fri Dec 06, 2002 2:18 am
Posts: 635
|
|
@ grumnus,
Welcome to the Forum
The problem you are describing appears to related to the use of poor quality blank Media. Suggest obtaining known proven quality Media such as Taiyo Yuden or Verbatim Media that consistently produces quality error free results.
Regards,
Coaster
|
|
| Top |
|
|
|
|
Posted: Sun Oct 21, 2007 12:42 am |
|
Joined: Sat Oct 20, 2007 11:20 am
Posts: 3
|
PumaUK wrote: Quote: i thinks something in windows system because when i try to
open the data of my burned DVDs a message come and tell me:
"access no possible" and other time tell me: disk is damage or no compatible with windows 1) try reading them in safemode 2) unistall all ide drivers and restart the system these problems are more system related than firmware have started the system in safe mode , but it
|
|
| Top |
|
|
|
|
Posted: Sun Oct 21, 2007 12:53 am |
|
Joined: Sat Oct 20, 2007 11:20 am
Posts: 3
|
Coaster wrote: @ grumnus,
Welcome to the Forum
The problem you are describing appears to related to the use of poor quality blank Media. Suggest obtaining known proven quality Media such as Taiyo Yuden or Verbatim Media that consistently produces quality error free results.
Regards,
Coaster
Hi Coaster,
the DVDs i have using until now to archiving my data are from Verbatim , else from Intenso. 5 disk cost zirka 6 euro + tax
|
|
| Top |
|
|
|
|
Posted: Sun Oct 21, 2007 2:08 am |
|
| Coaster |
| Posting Wizard |
|
Joined: Fri Dec 06, 2002 2:18 am
Posts: 635
|
grumnus wrote: .....The only problem I have is that my 107D can not read my burned DVDs any more
CD-ROM ( 700 MB ) is ok can read
DVDs (films) is ok can read etc etc.
When I try to open the data of my burned DVDs a message come and tell me:"access no possible" and other time tell me: disk is damage or no compatible with windows..... @ grumnus,
Summarizing your original Forum posting of Sat Oct 20, 2007 1:11 pm ->
Both 700MD CD Disks and Original Commercial DVD Movie Disks can be read with out any problems but ONLY personally burned DVD Disk Media cannot be read.
In seeing that Original Commercial DVD Movie Title Disks can be read properly on you computer clearly demonstrates that both your DVD Burner and your computer Windows Operating system is functioning correctly and can read DVD Media.
This leads to the question why you are receiving "Access Not Possible" and
|
|
| Top |
|
|
|
|
Posted: Sun Oct 21, 2007 11:10 am |
|
| Puma |
| Administrator |
|
Joined: Tue May 11, 2004 3:02 pm
Posts: 10124
Location: UK
|
|
| Top |
|
|
|
|
Posted: Tue Jan 01, 2008 9:57 am |
|
Joined: Tue Jan 01, 2008 9:49 am
Posts: 1
|
|
I apologize if this has been covered elsewhere, but my search did not turn any thing up.
Why has development on DVRFlash stopped? Has the architecture of the newer Pioneer drives changed so much that updating DVRFlash is pointless? Has the author gafiated? Been abducted by Pioneer agents in black helicopters?
|
|
| Top |
|
|
|
